
A spray foam rig drum holder should fit the way your crew loads, sprays, and changes material. In an existing spray foam trailer, that means checking more than open floor space. Plan the mount, pump access, and drum change path before you install the set.
Start With the Two-Drum Holder Set
Spray Foam Systems offers the 2 Drum Holder Set, part number 238608. The product listing describes a complete set of two holders with fluid tubes for spray foam material handling. Before you order, confirm the set configuration, drum fit, and required mounting parts with SFS.
For a retrofit, also share your current rig layout. Photos and measurements can help show where the holders may fit. However, the installer still needs to check the trailer structure and mounting requirements before work starts.
Choose a Spray Foam Rig Drum Holder Location
Map the Space Around the Drums
First, measure the proposed space with the drums, pumps, and nearby gear in mind. Include doors, shelves, hose racks, and service panels. Then mark the planned footprint on the floor so your crew can review the layout.
Next, check how the space works during a normal workday. A holder may fit against a wall yet leave too little room to reach a fitting. Likewise, an open floor area may be part of the path used to load fresh drums.
Check Mounting Support and Loaded Weight
Before drilling, have the installer confirm suitable mounting points and the required hardware. They should also check beneath the floor for wiring, plumbing, and other parts. Follow the holder and trailer requirements for support, backing, and attachment.
Also, review the loaded trailer weight and weight distribution. Include full drums, spare material, equipment, and tools. Choose the spray foam rig drum holder location with the trailer builder or a qualified rig installer so the layout stays within rated limits.
Keep Material Access Clear in Your Spray Foam Trailer
Plan the Full Drum Change Path
Start at the loading door and trace the route to each holder. Account for the drum handling equipment your crew uses. Then check that a fresh drum can reach its place while the other equipment remains in its normal position.
Next, allow room to remove an empty drum and work at its top. Check overhead space for pump removal, as well as access to bungs and connections. If your setup uses drum heaters or an agitator, include their space and access needs too.
Check Pump and Hose Routing
Keep A-side and B-side equipment clearly identified during the layout review. Also, check that hoses can reach their connections without sharp bends, pinched sections, or strain. Follow the pump and hose manufacturers’ routing requirements.
Finally, leave access for routine checks and service. Your crew should be able to inspect connections and reach required controls. Keep doorways, walkways, and equipment ventilation openings clear as you refine the plan.
Review the Layout Before Installation
Once the plan is marked out, walk through it with your crew and installer. Use this short checklist to review the spray foam rig drum holder retrofit:
- Confirm the set contents, dimensions, and drum compatibility.
- Verify mounting support, hardware, and loaded trailer limits.
- Check the loading route and empty drum removal path.
- Allow room to lift pumps and reach drum connections.
- Review hose routing, service access, and travel securement requirements.
A useful upgrade should support daily material handling as well as the finished layout. Before the rig returns to work, have the installer verify the completed mounting and required drum securement. Then review the drum change process with the crew.
Contact Spray Foam Systems about the Two-Drum Holder Set (238608) and share your spray foam trailer layout before you order.
FAQs
1. Can I add a two-drum holder set to an existing trailer?
A retrofit may be possible after a review of the space, structure, and loaded weight. Have SFS and your installer confirm fit and mounting needs for your trailer.
2. Where should a spray foam rig drum holder go?
Choose a supported location that allows drum changes, pump removal, and service access. The best position also depends on the trailer’s load limits and weight distribution.
3. What should I send SFS before ordering?
Send interior photos, floor measurements, drum sizes, and pump details. Also, show the loading door, nearby equipment, and the spot where you plan to mount the holders.
About Spray Foam Systems
Spray Foam Systems is the #1 spray foam rig builder and spray foam equipment supplier in the United States. Family-owned and proudly serving the industry since 2007, we operate from a 7-acre campus with over 80,000 square feet of dedicated working space in Greensboro, GA. With over 10,000 customers served over the last 18 years, we specialize in delivering high-quality turnkey spray foam systems, distributing top-tier equipment and supplies, and providing nationwide service and training to help contractors grow and succeed in the spray foam insulation and roofing markets.